introduction

Due to factors such as cost and quality of video communication, video phones have been neglected by users since its introduction until now. Now because of technological progress and the popularization of broadband Internet, videophones are showing new vitality. Industry experts predict that in the next few years, video phones will not only be able to interconnect with fixed-line telecommunications, PHS, mobile / Unicom mobile phones, but also with 3G mobile phones. Videophone will become an independent industry with good development prospects.

Based on a single 600 MHz TMS320DM643 (referred to as DM643) digital media processor from TI, I developed a set of embedded IP video phones with excellent performance and low prices to achieve real-time point-to-point network audio and video communication.

1 Hardware design based on TMS320DM643

DM643 digital media processor [1] integrates a series of peripherals to adapt to the development of video and imaging technology. It includes 3 configurable video ports, 1 10/100 Mbps Ethernet MAC (EMAC), 1 serial port for audio applications (McASP), 1 serial port (McBSP) and some other peripherals. There are 8 parallel processing units in the C64x core, using VLIW (Very Long Instruction Set) structure, processing capacity up to 4800MIPS, and 88 instructions are expanded on the basis of C6OOO common instruction set. These instructions enable C64x to more easily execute algorithms in image processing.

The composition of the embedded IP video phone based on a single DM643 is shown in Figure 1. The video signal input from the camera and the audio signal input from the microphone are sent to the DSP after A / D conversion. The DSP compresses, encodes, and merges the audio / video signal; then the data is transmitted through the local area network or the Internet, and from the network The received data is shunted, and the video signal is decoded and displayed and the audio signal is decoded and played separately. In the system, a keyboard is also connected through the McBSP / UART port of DM643 to realize the dialing function of the phone.


Figure 1: The composition of an embedded IP videophone

1.1 Video capture circuit

The video decoding chip used in this system is the SAA7l15 of Philips. The full TV signal input from the camera passes through clamping, anti-aliasing filtering, A / D conversion, YuV separation circuit inside the SAA7l15, in the conversion circuit of YuV to YCrCb Converted to BT.656 video data stream, input to the compression core unit DM643 through the video port VPo of DM643. The line / field synchronization signal of the video data is included in the EAV (End of AcTIve Video) and SAV (Startof AcTIve Video) time-base signals of the BT.656 digital video data stream. The video port only needs a video sampling clock and a sampling enable signal. SAA7l15 internal register parameter configuration and status read through 1 C bus. The principle of the video capture interface is shown in Figure 2.


Figure 2: The principle of the video capture port

DM643 sends the decoded video data to SAA7121 for display output through the video port VP1 channel. SAA7121 is a video coding chip of Philips, which can realize D / A conversion of digital video. The working mode of SAA7121 is determined by its internal control register, and the initialization of the control register is completed through the 1 C bus. DM643 uses its own 1 C bus module as the main controller to parameter control SAA7121.

1.3 Audio input / output circuit

This system uses TI's high-performance stereo codec TI V320AIC23 (referred to as AIC23) to achieve the collection and playback of audio signals. AIC23 is compatible with the DM643 I / 0 voltage and can be seamlessly connected to the DM643 McASP interface.

In this system, AIC23 works in the main mode, the sampling word width of the left and right channels are 16 bits. The data interface is in DSP mode. Set the working parameters and feedback status information of internal registers through the 12 C bus.

Due to the inherent characteristics of network transmission, audio data and video data cannot be uniform when transmitted to the receiver. If the sender does not make any corrections, it is difficult to guarantee the synchronized output of audio / video. In order to achieve sampling synchronization of audio and video, a phase-locked loop PI I 1708 is used. A 27 MHz clock is output from the UC pin of SAA7115, and the default clock frequency of 18.433 MHz is output via the SCKO 3 pin of PLI 1708 as the input master clock MCI of AIC23 The clock used in K.AIC23 can be obtained by dividing the main clock MCLK by setting the register. Since the audio and video sampling signals use the same clock source, there will be no problem of audio / video out of synchronization.

Strip light with both RGB colorful light and warm light, the length of the strip light is 2 meters, 60pcs LED lamp beads inside are high-quality and energy-saving , the light source is stable without strobe.


The installation is very simple, just need to peel off the 3M glue on the back, you can paste and decorate any place.


With the exclusive designed 2.4G remote controller, get you off the switch and turn on / off the lights anywhere, one remote controller can set 4 groups, each group is recommended to match up 8pcs bulbs, one remote controller can max control 32 bulbs. This remote controller is suitable for all 2.4G version of RGBW products under [linkuphome".

remote


The remote control uses colorful touch buttons, the color touch buttons are comfortable and sensitive. The remote controller has the functions of grouping, lighting, brightness adjustment, color light automatic cycle mode, three cycle speeds can be choosed. The wireless control distance is around 20 meters. Low power consumption makes the remote controller only need 4pcs AA batteries, but can be used for two years.


Product Parameters

Description: Smart RGB Strip Light with 2.4G Remote Control
Control Qty: 1-48 pcs 
Control distance: 20m
Material: Polyurethane with 3M back adhesive
Working  Voltage: 100-240V
Frequency: 50/60Hz
Lamp Color: RGB+Warm White
Color Temperature: 3000K
Meters: 2 Meters
LED Power: 7W 
Power Adapter: 12V/2A
Product Specification: 30pcs LED beads/M, 2 M/root, total 60pcs LED beads.
(3pcs strip lights can be connected, max to 6 meters.Need customized. Pls inform in advance if needed)
Warranty: 2 Years
Color box  size: 20*18*4.8cm
G.W. of  Unit: 0.29kg
N.W. of Unit: 0.21kg

Discreption: 2.4GRF Wireless RGB Remote Controller 
Product dimension: 105mm *33mm, 
Product Net Weight: 150g
Material: ABS & Metal
Battery: 4*AA battery (not included) 
Working Power: 6V
Standby Power: 3 mW
Frequency Band: 2400-2483.5MHz/2.4GHz
Control Distance: 20m
Control bulb qty: 1-32 pcs
Packing: Each in a color box
Warranty: 1 Year
Color box  size: 16.7*14.7*4.5cm
G.W. of  Unit: 0.22kg
N.W. of Unit: 0.15kg

Strip Light With Remote Control

Strip Light With Remote Control,Remote Control LED Lights Battery Powered,Remote Control Strip Light,Remote Control Flashing Strip Light

Ningbo Homey Photoelectric Technology. Co., Ltd , https://www.linkuphome.com